Martin Professional MAC 2000 Profile II Manual de usuario

MAC 2000 Profile IIuser manual

10 MAC 2000 Profile II4 Move the brown wire on the ballast connection block tothe position shown Figure 9.5 Close the base before applying power. Pow

Data 11DATAImportant! Never connect more than 1 data input and 1 data output. The MAC 2000 Profile II has both 3-pin and 5-pin XLR sockets for DMX in

12 MAC 2000 Profile IIRIGGINGThe MAC 2000 Profile II can be placed on stage or clamped to a truss in any orientation. The Fast-Lock systemenables qui

Control panel 13CONTROL PANELThe LED control panel is used to set the address and personalities, read lamp hours and other information, calibrateeffe

14 MAC 2000 Profile IIIf tracking mode movement is not satisfactory there are 2 parameters that can be adjusted. The first is selected underPERS/TRAC

Control panel 15Firmware versionINFO/VER displays the version number of the installed firmware. The firmware version is also displayed briefly atstar

16 MAC 2000 Profile II3 Pan calibration is most useful when multiple fixtures are stacked vertically. To calibrate, set zoom, focus, iris,and tilt po

Optical configuration 17OPTICAL CONFIGURATIONGobosSpecificationsAll gobo slots including the seven color/gobo wheel positions accept round theatrical

18 MAC 2000 Profile IIReplacing rotating gobosImportant! The gobo can fall out if the spring is inserted backwards. 1 Disconnect the fixture from pow

Optical configuration 192 Lock the head in the upside down position and remove the bottom cover. Turn the color/gobo wheel asrequired to access the d

74361348817140810° 28°133½°133½°271759270°270°490530545min c/cmin c/c© 2000-2002 Martin Professional A/S, Denmark. All rights reserved. No part of thi

20 MAC 2000 Profile IIEFFECTSThe MAC 2000 Profile II is compatible with USITT DMX512 controllers. The fixture has two DMX operating modes,8-bit and 1

Effects 21Effect wheelThe effect wheel provides a variable frost filter and two rotating slots that house a beam shaper and a three-facet prism.The p

22 MAC 2000 Profile IIROUTINE MAINTENANCEThe MAC 2000 Profile II requires routine cleaning. The schedule depends heavily on the operating environment

Routine maintenance 23Software installationSoftware updates are installed in the MAC 2000 Profile II using a Martin MP-2 Uploader or a LightJockey 40

24 MAC 2000 Profile IIDMX PROTOCOL DMX channel Start code = 08-bit 16-bit Value Percent Function1 0 - 1920 - 4950 - 7273 - 7980 - 99100 - 119120 - 12

DMX protocol 2570 - 2020 - 4040 - 6060 - 8080 - 100 100 - 120120 - 140140 - 160160 - 163164 - 167168 - 171172 - 175176 - 179180 - 183184 - 187188 - 1

26 MAC 2000 Profile II990 - 2550 - 2 3 - 127128 - 252253 - 2550 - 1000 - 11 - 50 50 - 9899 - 100Gobo Wheel 1, Position/Velocity Coarse Position (MSB)

DMX protocol 2712 1401 - 175 176 - 183184 - 191192 - 199200 - 207208 - 215216 - 220221 - 225226 - 230231 - 235236 - 240241 - 245246 - 250251 - 25501

28 MAC 2000 Profile IICONTROL MENU Menu Item Options Notes (Default settings in bold print)AddR - 1-512DMX addressPSET -8bitFull control with coarse

Control menu 29INFOTIME/HRS TOTLTotal hours of operation since fabricated RSETHours of operation since counter reset. To reset, display counter and p

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Safety informatio

30 MAC 2000 Profile IIMANRST -Reset fixtureL ON -Lamp onLoFF -Lamp offSHUTOPENOpen shutterCLOSClose shutterSTRFFast strobeSTRMMedium strobeSTRSSlow s

Control menu 31MANcont.gOb2OPENGobo wheel 2. Open positiong1 I-g5 IGobo wheel 2. Indexed gobos 1→5g1 g-g5 RGobo wheel 2. Rotating gobos 1→5g1IS-g5ISG

32 MAC 2000 Profile IIUTIL(Press and hold Enter for a few seconds to use this menu)FEbAONEnable pan/tilt position correction systemOFFDisable pan/til

Adjustment submenu 33ADJUSTMENT SUBMENUThis menu is located under UTIL/Adj.Menu Item Options NotesRST - -Reset fixture L ON - -Strike lampLoFF - -Dou

34 MAC 2000 Profile IIDISPLAY MESSAGESMessage Appears when... What to doRST (Reset) ... the fixture is indexing effects at startup. Wait for reset t

Troubleshooting 35TROUBLESHOOTING Problem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture.Check that power

36 MAC 2000 Profile IICIRCUIT BOARD CONNECTIONS

Specifications MAC 2000 Profile II 37SPECIFICATIONSMAC 2000 PROFILE IINote that versions with electronic ballast are denoted with an ‘E’. PHYSICALLen

38 MAC 2000 Profile IIMAXIMUM POWER AND CURRENT - ELECTRONIC BALLAST100 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 MAC 2000 Profile IIINTRODUCTIONThank you for selecting the MAC 2000 Profile II. This extraordinary 1200 watt luminaire from Martin Professionalprov

Transportation 5TRANSPORTATIONImportant! Release the transport locks before operating the fixture. Included itemsThe MAC 2000 Profile II is shipped i

6 MAC 2000 Profile IIDouble flight caseUnpacking1 Open the flight case and pull the drawer all the way out. 2 Release the head (tilt) transport lock.

Lamp 7LAMPAbout the HMI 1200 W/S lampThe MAC 2000 Profile II comes with a double-ended OSRAMHMI 1200 W/S discharge lamp installed. This highly-effici

8 MAC 2000 Profile II4 See Figure 6. With the nipple on the bulb facing the back,insert the right end of the new lamp in the socket. Pull upon the le

AC power 9AC POWERWARNING! For protection from electric shock, the fixture must be grounded (earthed). The AC mains supply shall be fitted with a fu